The FIX Z XTREM A4 Stud Anchor is a true-to-size, heavy duty, torque controlled expansion anchor, for permanent anchoring into standard and hard concrete. Designed for heavy duty anchoring in cracked and non- cracked concrete. Suitable for seismic and fire environments.

Features and Benefits
Substrates
Installation
Typical Applications
  • 3 legs clip for a better expansion
  • 6 lugs for a better fixing in concrete
  • Improved efficiency with fewer hammer blows and turns for installation
  • “Pull down” capabilities for secure fixing
  • Concrete (cracked and non-cracked), Solid Stone (applicable with care)
  1. Drill the correct diameter hole to the same diameter as the FIX Z stud anchor
  2. Remove debris from hole by blowing out with compressed air or hand held blow out
  3. Install the anchor in the hole with a hammer until washer seats on
  4. Tighten bolt with a torque wrench to recommended assembly
  • Structural beams and columns
  • Load bearing zones
  • Cable trays
  • Overhead piping
  • Air condition ducts
  • Securing of machines and equipment
  • Tie back brackets for façade
Features and Benefits
  • 3 legs clip for a better expansion
  • 6 lugs for a better fixing in concrete
  • Improved efficiency with fewer hammer blows and turns for installation
  • “Pull down” capabilities for secure fixing
Substrates
  • Concrete (cracked and non-cracked), Solid Stone (applicable with care)
Installation
  1. Drill the correct diameter hole to the same diameter as the FIX Z stud anchor
  2. Remove debris from hole by blowing out with compressed air or hand held blow out
  3. Install the anchor in the hole with a hammer until washer seats on
  4. Tighten bolt with a torque wrench to recommended assembly
Typical Applications
  • Structural beams and columns
  • Load bearing zones
  • Cable trays
  • Overhead piping
  • Air condition ducts
  • Securing of machines and equipment
  • Tie back brackets for façade
FIX Z XTREM Stainless Steel A4 - Recommended Working Loads in 40N/mm2 non-cracked Concrete
Thread
Ø
Embedment
Depth (mm)
Torque
(Nm)
Shear Load
(kN)*
Tension Load
(kN)*
M848208.24.0
M1060458.96.7
M12707513.49.6
M168511021.212.9

 

* Safety factor for all loads = 3

* This table does not consider edge distance and anchor spacing effects. Please refer to Ramset Design Guide for more information.

* Pull out test for single anchor = working load x 1.5

 

FIX Z XTREM A4 Stud Anchors - Stainless Steel A4
Part No.DescriptionThread
Ø
Max Fixture
Thickness (mm)*
Fixture Clearance  Hole Ø(mm)Overall Anchor
Length (mm)
Drilled Hole
Ø (mm)
Min Hole
Depth (mm)*
Order Qty
058616M8x55/5 A4M85956852100
058617M8x70/20-7 A4M820971852100
058618M8x90/40-27 A4M84099185250
058619M10x70/10 A4M10101270105550
058620M10x95/35-15 A4M10351295105550
058621M10x105/45-25 A4M104512105105525
058622M10x130/70-50 A4M107012130105525
058623M12x95/20 A4M12201495127025
058624M12x110/35-15 A4M123514110127025
058625M12x120/45-25 A4M124514120127025
058626M12x140/65-45 A4M126514140127025
058627M16x120/20 A4M162018120169020
058628M16x140/40-20 A4M164018140169010

* Data based on minimum anchor depth