The FIX Z XTREM Anchor is a heavy duty, torque controlled expansion anchor, with an integrated pull- down section, designed for high performance in both static and dynamic load applications, in both cracked and non-cracked concrete. The FIX Z XTREM Anchor is ideally suited for through fixing into concrete when security and reliability are paramount.

Categories:
Features and Benefits
Substrates
Installation
Typical Applications
  • 3 legs clip for a better expansion
  • 6 lugs for a better fixing in concrete
  • Improved efficiency with fewer hammer blows and turns for installation
  • “Pull down” capabilities for secure fixing
  • Concrete (cracked and non-cracked), Solid Stone (applicable with care)
  1. Drill the correct diameter hole to the same diameter as the FIX Z stud anchor
  2. Remove debris from hole by blowing out with compressed air or hand held blow out
  3. Install the anchor in the hole with a hammer until washer seats on
  4. Tighten bolt with a torque wrench to recommended assembly
  • Structural beams and columns
  • Load bearing zones
  • Cable trays
  • Overhead piping
  • Air condition ducts
  • Securing of machines and equipment
  • Tie back brackets for façade
Features and Benefits
  • 3 legs clip for a better expansion
  • 6 lugs for a better fixing in concrete
  • Improved efficiency with fewer hammer blows and turns for installation
  • “Pull down” capabilities for secure fixing
Substrates
  • Concrete (cracked and non-cracked), Solid Stone (applicable with care)
Installation
  1. Drill the correct diameter hole to the same diameter as the FIX Z stud anchor
  2. Remove debris from hole by blowing out with compressed air or hand held blow out
  3. Install the anchor in the hole with a hammer until washer seats on
  4. Tighten bolt with a torque wrench to recommended assembly
Typical Applications
  • Structural beams and columns
  • Load bearing zones
  • Cable trays
  • Overhead piping
  • Air condition ducts
  • Securing of machines and equipment
  • Tie back brackets for façade
FIX Z XTREM - Zinc Plated - Recommended Working Loads in 40N/mm2 non-cracked Concrete
Thread
Ø
Embedment
Depth (mm)		Torque
(Nm)		Shear Load
(kN)*		Tension Load
(kN)*
M846204.63.8
M1060455.38.4
M1270607.712.5
M168511015.016.6
M2010016020.421.3

 

* Safety factor for all loads = 3

* This table does not consider edge distance and anchor spacing effects. Please refer to Ramset Design Guide for more information.

* Pull out test for single anchor = working load x 1.5

 

FIX Z XTREM Stud Anchors - Zinc Plated
Part No.DescriptionThread
Ø		Max Fixture
Thickness (mm)*		Fixture Clearance
Hole Ø (mm)		Overall Anchor
Length (mm)		Drilled Hole
Ø (mm)		Min Hole
Depth (mm)*		Order
Qty		Seismic
Approval
057763M8x65/5M85965860100C1
057764M8x75/15M815975860100C1
057765M8x90/36M83099086050C1
057788M8x130/70M870913086050C1
057768M10x85/5M1051285107550C1/C2
057769M10x90/10M10101290107550C1/C2
057771M10x120/40M104012120107525C1/C2
057773M10x160/80M108012160107525C1/C2
057774M12x100/5M12514100129025C1/C2
057776M12x115/20M122014115129025C1/C2
057777M12x135/40M124014135129025C1/C2
057778M12x155/60M126014155129025C1/C2
057779M12x180/85M128514180129025C1/C2
057781M16x145/25M1625181451611010C1/C2
057782M16x170/50M1650181701611010C1/C2
057783M16x180/60M1660181801611010C1/C2
057785M20x170/30M2030221702013010C1/C2
057787M20x220/80M2080222202013010C1/C2

* Data based on minimum anchor depth

Download PDF

Related products

Read more

EPCON G5 PRO High Strength Epoxy Adhesive
Read more

TRIGA Z A4 Heavy Duty Structural Anchor
Read more

PRO6
Read more

Safety Ring Anchor System
Read more

CIM Cast In Anchor
Read more

TCM Cast In Anchor
Read more

TRIGA Z XTREM Heavy Duty Structural Anchor
Read more

AnkaScrew™ Screw-In Anchor
Read more

HIT M & HIT M-A2
Read more

FIX Z XTREM A4 Stud Anchor
Read more

VIPER XTREM TR
Read more

TAPCON HFL XTREM